| Author |
|
dolfans
Newbie
Joined: Feb 11 2010
Online Status: Offline
Posts: 25
Member's Gallery:
View Gallery
Location:
U.S. - North Carolina
|
| Posted: Feb 27 2010 at 10:49am | IP Logged
|
|
|
The drivers side window is down and will not come back up. IT is power windows and and king can extended cab whatever it is called. The pass side is fine. Anything i can do to get the window up asap. How much is a new switch anyone know. Would it be cheaper to get one at a junk yard Thanks
|
| Back to Top |
|
| |
davidjbrady
Senior Member
Joined: May 29 2009
Online Status: Offline
Posts: 354
Member's Gallery:
View Gallery
Location:
U.S. - California
|
| Posted: Feb 27 2010 at 2:58pm | IP Logged
|
|
|
Usually,whne it is down and does not go back up, the window has fallen out of the track.You should be able to put it back in the track and slide it up to hold it in place. It may not even be the switch that is bad
__________________
08 Frontier CC, 4X4, LWB
15 Altima S
Sacramento, CA
|
| Back to Top |
|
| |
dolfans
Newbie
Joined: Feb 11 2010
Online Status: Offline
Posts: 25
Member's Gallery:
View Gallery
Location:
U.S. - North Carolina
|
| Posted: Feb 28 2010 at 9:04am | IP Logged
|
|
|
I have the panel off and i tried to pull the window up. I can not even get it to move a hair.
|
| Back to Top |
|
| |
frontierguy
Senior Member
Master Mechanic
Joined: May 20 2008
Online Status: Offline
Posts: 2591
Member's Gallery:
View Gallery
Location:
U.S. - Pennsylvania
|
| Posted: Mar 02 2010 at 3:50pm | IP Logged
|
|
|
While holding the switch in the up position, tap on the motor or door panel, possible brushes are sticking in the motor.
__________________
'10 Altima SL
Traded 08 Frontier for 16 Frontier SV CC Long box, quite an upgrade. I do miss the 6 speed and Dynomax ex.
Nissan Technician 25 + years
2011 John Deere X720SE
|
| Back to Top |
|
| |
dolfans
Newbie
Joined: Feb 11 2010
Online Status: Offline
Posts: 25
Member's Gallery:
View Gallery
Location:
U.S. - North Carolina
|
| Posted: Mar 04 2010 at 12:29pm | IP Logged
|
|
|
I am very sure the motor is good. I tried to raise it up by getting some wire to the blue/black wire(upwire). I had some 10 gage wire and a toggle and a ground to the door. Nothing. I then tried the factory switch again and nothing. The motor did get a extra load in the down postion of the button. I tried pulling the window alone and with the switch being used. Can anyone know what i can do or another website for help. Thanks
|
| Back to Top |
|
| |
frontierguy
Senior Member
Master Mechanic
Joined: May 20 2008
Online Status: Offline
Posts: 2591
Member's Gallery:
View Gallery
Location:
U.S. - Pennsylvania
|
| Posted: Mar 04 2010 at 8:06pm | IP Logged
|
|
|
BY reversing the polarity on the motor wires determines the direction the motor turns. If you run power and ground one way the motor goes up, reverse them it should go down.Does the motor appear to be straining like bound up??? It is very possible the cable has broke on the regulator assy.
__________________
'10 Altima SL
Traded 08 Frontier for 16 Frontier SV CC Long box, quite an upgrade. I do miss the 6 speed and Dynomax ex.
Nissan Technician 25 + years
2011 John Deere X720SE
|
| Back to Top |
|
| |
pbody
Newbie
Joined: May 05 2009
Online Status: Offline
Posts: 2
Member's Gallery:
View Gallery
|
| Posted: Mar 18 2010 at 11:50pm | IP Logged
|
|
|
I'm having the same problem on a 2000 Frontier, but no recall on 2000's. I've taken the door panel off and see where the motor is, but I'm totally clueless on how to go about removing the motor with regards to the window cable. Can't find any instructions or diagrams. Can someone provide some insight or point me in the right direction? Thanks!
|
| Back to Top |
|
| |
dolfans
Newbie
Joined: Feb 11 2010
Online Status: Offline
Posts: 25
Member's Gallery:
View Gallery
Location:
U.S. - North Carolina
|
| Posted: Mar 19 2010 at 9:25am | IP Logged
|
|
|
the cable looks fine. i got some wire a a toggle switch and put a wire to the truck for ground and one to the up wire and nothing. I tried the pass switch and nothing. but did find out the pass switch has to be connected. a new switch for drivers side 2 door is form $103.00 to $150.00 dealerships
|
| Back to Top |
|
| |
frontierguy
Senior Member
Master Mechanic
Joined: May 20 2008
Online Status: Offline
Posts: 2591
Member's Gallery:
View Gallery
Location:
U.S. - Pennsylvania
|
| Posted: Mar 19 2010 at 8:09pm | IP Logged
|
|
|
Try pulling up very hard on the switch, sometimes this will allow them to operate. You can not pull the window up by hand with the motor and regulator connected. When you are trying to hot wire it, are you sure you have a good ground to the chassis and not to the door?
__________________
'10 Altima SL
Traded 08 Frontier for 16 Frontier SV CC Long box, quite an upgrade. I do miss the 6 speed and Dynomax ex.
Nissan Technician 25 + years
2011 John Deere X720SE
|
| Back to Top |
|
| |
Active Topics 
Memberlist 
Search 
Help 
Register 
Login
Nissan Frontier Forums : Problems / Technical
Topic: power window down
