Nissan Frontier Forums

Affiliate Site : Nissan Titan Forums
  Active TopicsActive Topics  Display List of Forum MembersMemberlist  Search The ForumSearch  HelpHelp  Photo GalleryPhoto Gallery
  RegisterRegister  LoginLogin

Sponsored Links

Problems / Technical
 Nissan Frontier Forums : Problems / Technical
Subject Topic: Timing Chain / Cam Shift? Help! Post ReplyPost New Topic
Author
Message << Prev Topic | Next Topic >>
FireCloud
Newbie
Newbie


Joined: Jul 27 2019
Online Status: Offline
Posts: 1

Member's Gallery:
View Gallery




Location:
U.S. - Colorado
Posted: Jul 30 2019 at 7:21pm | IP Logged Quote FireCloud

Hi Guys,

I messed up...during the timing chain replacement job I didn't do a couple of things that I should have and now I have a mess on my hands.

Not all of my paint marks survived and one of the cams rotated on me. To top it all off, I think that I was 180 degrees off from TDC. It's still all in pieces and I'm considering giving in to a local mechanic, but that's never been my nature.

Does anyone know how to align the cams, the gears, crank etc...from scratch? I was planning on installing new chains, already did the tensioners and even have new secondary gears. All of this on a 66k mile pristine truck...kinda makes me sick.

Back to Top View FireCloud's Profile Search for other posts by FireCloud
 
lakota
Moderator Group
Moderator Group
Avatar
Nissan Frontier Forums Moderator

Joined: Feb 14 2005
Online Status: Offline
Posts: 1815

Member's Gallery:
View Gallery


Location:
U.S. - Texas
Posted: Jul 31 2019 at 1:41pm | IP Logged Quote lakota

..

Sad to hear.
Please add year and engine.
it might have been four or more.

Good Luck.. Don S..

__________________
PLEASE >>> A SIG similar to mine can be VERY HELPFUL to all the members!
'99 4x4 3.3 Frontier Se KC Auto, 48,000 miles
'76 4x4 401 Wagoneer QT
'04 FWD 1.8 Sentra '08 FWD 2.4 Camry LE
Fort Worth
Back to Top View lakota's Profile Search for other posts by lakota Visit lakota's Homepage
 
Rubble
Moderator Group
Moderator Group
Avatar

Joined: Jul 31 2014
Online Status: Offline
Posts: 311

Member's Gallery:
View Gallery


Location:
United States
Posted: Aug 01 2019 at 11:27am | IP Logged Quote Rubble

FireCloud wrote:
Hi Guys,

I messed up...during the timing chain replacement job
I didn't do a couple of things that I should have and
now I have a mess on my hands.

Not all of my paint marks survived and one of the cams
rotated on me. To top it all off, I think that I was
180 degrees off from TDC. It's still all in pieces
and I'm considering giving in to a local mechanic, but
that's never been my nature.

Does anyone know how to align the cams, the gears,
crank etc...from scratch? I was planning on
installing new chains, already did the tensioners and
even have new secondary gears. All of this on a 66k
mile pristine truck...kinda makes me sick.


FC,

If you cannot figure it out by following the Nissan
Service Manual, IMO it's time to take it to The Best
Nissan Engine Mechanic that You can Find.

If it were mine, I would have it loaded on a Flatbed
Wrecker and haul it to a Nissan Service Department.
But before hand,, I would talk with the Nissan Master
Tech to see if he is willing to take this on. It's
not going to be cheap,, but on the otherhand,, it's
going to cost a lot more,, if it isn't done Correctly.

By now you know how important it is to read, follow
the procedure in the Service manual,, and Reread and
understand it all before starting this Maintenance.

These are INTERFERANCE Engine's in that if the Timeing
is not correct,, the Valve's can contact the Top of
the Piston's. If that happen's then there is a lot
more cost and Part's to Replace.

At some point when digging a hole, it's time to stop
digging and get yourself out of the hole before you
can't get out at all,, even with other's trying to
help.

Bite the bullet, Get Some Help and be prepared for the
Bill,

Regards,

__________________
Barney
2013 SV V6 Frontier KC/AT/2WD; Previous 20 yrs ~ '93 I4 Hardbody KC/AT/2WD, Sold.
Back to Top View Rubble's Profile Search for other posts by Rubble
 
frontierguy
Senior Member
Senior Member

Master Mechanic

Joined: May 20 2008
Online Status: Offline
Posts: 2591

Member's Gallery:
View Gallery


Location:
U.S. - Pennsylvania
Posted: Sep 01 2019 at 10:52am | IP Logged Quote frontierguy

The chains should have "bright" links to establish
proper location in relation to sprockets.

__________________

'10 Altima SL
Traded 08 Frontier for 16 Frontier SV CC Long box, quite an upgrade. I do miss the 6 speed and Dynomax ex.


Nissan Technician 25 + years
2011 John Deere X720SE
Back to Top View frontierguy's Profile Search for other posts by frontierguy
 

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

  Post ReplyPost New Topic
Printable version Printable version

Forum Jump
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Sponsors

Powered by Web Wiz Forums version 7.92
Copyright ©2001-2004 Web Wiz Guide
A Vebro Solutions Venture
Hosted by Vebro Hosts
Need a vacation? Find our more about a Hawaii Vacation or get Hawaii insider tips!